Murphy PowerView PV-101 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Motor Murphy PowerView PV-101. Murphy PowerView PV-101 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - PowerView™

Rev 09-10-08 00-02-0605 Catalog Section 78 PowerView™ Model PV-101 User’s Guide

Strany 2

00-02-0605 - 6 - Rev 09-10-08 2. Touching the Arrow Keys will move the selection bar to other menu items.

Strany 3 - Table of Contents

00-02-0605 - 7 - Rev 09-10-08 3. Certain menus have multiple pages of items. Scrolling past the top item or bottom item on the current page will r

Strany 4

00-02-0605 - 8 - Rev 09-10-08 4. When the desired item is highlighted by the cursor, pressing Enter will select that item and display the correspo

Strany 5 - Introduction

00-02-0605 - 9 - Rev 09-10-08 Operation PowerView Menus (First Time Start Up) 1. When power is first applied to the display, the Murphy logo appea

Strany 6

00-02-0605 - 10 - Rev 09-10-08 2. If the Engine ECU is broadcasting a 'Wait To Start' message, this screen will be shown. Engine manufac

Strany 7 - Faceplate Features

00-02-0605 - 11 - Rev 09-10-08 3. Once the engine has started, the single engine parameter appears with the engine RPM displayed. Pressing the Rig

Strany 8

00-02-0605 - 12 - Rev 09-10-08 Setting Up the Display The screen may be configured to display a single engine parameter (1-up display), or four par

Strany 9 - Basic Navigation

00-02-0605 - 13 - Rev 09-10-08 1-Up Display Settings 1. Touch Menu and use the Arrow Keys to highlight SETUP 1-UP DISPLAY, then press Enter. 2. To

Strany 10

00-02-0605 - 14 - Rev 09-10-08 6. Continue to scroll and select additional parameters for the CUSTOM 1-UP DISPLAY. Touch Menu at any time to retur

Strany 11

00-02-0605 - 15 - Rev 09-10-08 4-Up Display The 4-up display places the parameter data into four areas of the screen known as quadrants. Factory de

Strany 12

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any

Strany 13 - Operation

00-02-0605 - 16 - Rev 09-10-08 5. Touch Enter and a list of parameters will appear. The parameter that is highlighted is the selected parameter fo

Strany 14

00-02-0605 - 17 - Rev 09-10-08 8. The parameter in the selected quadrant has changed to the parameter selected in the previous screen. 9. Repeat

Strany 15

00-02-0605 - 18 - Rev 09-10-08 Main Menu Options This section describes the features listed on the main menu of the PowerView. These menu options a

Strany 16 - 1-Up Display

00-02-0605 - 19 - Rev 09-10-08 Backlight Adjustment ADJUST BACKLIGHT allows you to select the desired backlight intensity. Contrast Adjustment From

Strany 17 - 1-Up Display Settings

00-02-0605 - 20 - Rev 09-10-08 Faults and Warnings The PowerView provides two means for detecting faults and warnings: visual LEDs on the casing (S

Strany 18

00-02-0605 - 21 - Rev 09-10-08 Auxiliary Gage Fault Murphy’s PVA Gages can be attached to the PowerView. If an auxiliary gage should fail, the 1-u

Strany 19 - 4-Up Display

00-02-0605 - 22 - Rev 09-10-08 Acknowledging Fault Codes 1. To acknowledge and hide the fault and return to the 1-up or 4-up display, touch Enter

Strany 20

00-02-0605 - 23 - Rev 09-10-08 Utilities Menu The following steps take place starting at the UTILITIES menu option. 1. GAGE DATA - View informatio

Strany 21

00-02-0605 - 24 - Rev 09-10-08 being used. Most engine ECU’s use Version 4, therefore in most cases adjustment of this menu option will not be requ

Strany 22 - Stored Fault Codes*

00-02-0605 - 25 - Rev 09-10-08 Modbus® Setup 1. From the UTILITIES menu, select MODBUS SETUP. 2. Select either the SLAVE ACTIVE (SCADA or remote

Strany 23 - Utilities

Table of Contents Introduction ... 1 Engine and Transmission Parameters 2

Strany 24 - Fault Indicators

00-02-0605 - 26 - Rev 09-10-08 Selecting Engine ECU 1. From the UTILITIES menu, choose SELECT ENGINE ECU. 2. The message “LISTEN TO ECU: ALL” is

Strany 25 - Derate / Shutdown Codes

00-02-0605 - 27 - Rev 09-10-08 Troubleshooting “WAIT TO START PREHEATING” is displayed The ECU is broadcasting a 'Wait To Start' message.

Strany 26 - Acknowledging Fault Codes

00-02-0605 - 28 - Rev 09-10-08 “NO STORED CODES” is displayed The PowerView sent a request to the ECU for Stored Fault Code (DM2) information, and

Strany 27 - Utilities Menu

00-02-0605 - 29 - Rev 09-10-08 “DATA ERROR” is displayed in place of a parameter value The ECU is sending a message that there is a data error with

Strany 28

00-02-0605 - 30 - Rev 09-10-08 NOTES

Strany 29 - Modbus® Setup

Murphy, the Murphy logo, and PowerView are registered and/or common law trademarks of Murphy Industries, Inc. This document, including textual matte

Strany 30 - Selecting Engine ECU

www.fwmurphy.com/products/murphylink/powerview.htm

Strany 31 - Troubleshooting

(THIS PAGE INTENTIONALLY LEFT BLANK)

Strany 32

00-02-0605 - 1 - Rev 09-10-08 Introduction Congratulations on purchasing your PowerView display, a multifunction tool that provides a window into t

Strany 33

00-02-0605 - 2 - Rev 09-10-08 Engine and Transmission Parameters The following are some of the engine and transmission parameters which may be disp

Strany 34

00-02-0605 - 3 - Rev 09-10-08 Faceplate Features

Strany 35

00-02-0605 - 4 - Rev 09-10-08 Navigation and Keypad Functions The keypad on the PowerView display is a capacitive touch sensing system. There are n

Strany 36

00-02-0605 - 5 - Rev 09-10-08 Basic Navigation 1. When Menu is pressed, the main menu items are displayed.

Komentáře k této Příručce

Žádné komentáře